Shared Cubelets Robots

Author: Gellert Nagy

This simple robot just will go towards a wall (barrier) stops before reaching goes back for 3 sec, stops and waits for 3 sec and drives forward again.

Author: Gellert Nagy

This simple robot just will go towards a wall (barrier) stops before reaching goes back for 3 sec, stops and waits for 3 sec and drives forward again.

Author: Ken McDaniel

Dud Light turns on its bulb when it sees light and turns off when it gets dark.

Author: mark gross

This basic maze-following robot follows walls to navigate a maze made of wo= oden blocks. The robot has two Distance Cubelets and two Drive Cubelets. = It turns away from a wall when it gets too close. You'll need two KT06 ki= ts to build this robot, or one KT01 kit.

Author: mark gross

This is a more sophisticated Edge Detector robot. It's like the Basic Edge Detector, but you can "tune" it using the Knob Cubelet. You'll need a Knob and a Minimum Cubelet, which aren't in the KT06 kit.

Author: mark gross

This simple three-block robot advances until the Distance Cubelet moves beyond the edge of the surface it's on, then stops. You can build this robot with just the Cubelets in the KT06 kit.

Author: mark gross

This robot made of only Distance and Flashlight Cubelets (and, of course, a= Battery Cubelet) has been on our coffee table at Modular Robotics for we= eks. Wave your hands over the surface and the Flashlight Cubelets light up.= It is fun to play with, and can be easily reconfigured to different layout= s.

Author: mark gross

A three Cubelet linear robot that follows you. You can lead it around with your hand.

Author: Bart Wessel

As I am getting older, and a Gobot would drive away too quickly, I decided = to reprogram a Knob-block to act as a limiter. No matter how much input it = gets, it's output will never exceed the knob-setting. The Distance block's input is used to sense the closeness of your hand. It = drives the Rotate block, which holds a BarGraph block as the tail. The Knob= block than provides limited signal to the three (for stability) Drive bloc= ks, the Speaker (it squawks) and the Flashlight (it winks at you).

Author: Sawyer Bernath

A prototype version of a Cubelets birthday cake! In the future I want to make a way to blow out the candle, and also maybe add a rotate (or two drives) for some extra pizzazz. Here's a little video tour: http://www.youtube.com/watch?v=LyGgevxO2oM&feature=youtu.be

Author: Matthew Capron

This robot will spin around when turned on. After an amount of time, the ro bot will stop. At this time a flashlight at the opposite end of the robot w ill illuminate the chosen individual. Another flashlight will flash wildly as a speaker will announce the stopping of the robot.

Author: Stephane Constantin

These are two seperate robots. The predator robot chases the prey robot. Ea= ch consists of 1 battery, 1 distance and 2 drives. The drives are the only = blocks that are reprogrammed. The prey drives uses code 13572.c and the pre= dator drives use code 7956.c. The predator moves forward until it gets clos= e to the prey. The prey moves away if it detects a predator close to it.

Author: Jon Hiller

Little robot that moves around the room randomly while avoiding obstacles. Just about as dumb as a Roomba and it doesn't even vacuum your floor!

Author: Kristin Yen

This is a simple snake robot with a flashlight head that shuffles forward.

Author: Emily Plage

This robot makes the flashlight strobe on and off and the speaker project robot beeps when the brightness sensor indicates low light

Author: Matthew Capron

This robot combines six cubes with simple functionality to build a complex robot that you can interact with! This robot can steer around the table to drive around a course or just around a table top! This robot can also be built with a Passive Cube in place of the Blocker Cube, see how it changes the functionality!

Author: Eric Lundby

A simple robot that performs a simple backup/turn routine once it detects an object in it's way.